June 2023 Meeting

by Joel Cool-Panama, Secretary, RRS.ORG


The Reaction Research Society held its monthly meeting at the Compton/Woodley Airport location, 7:30 PM PST.

Agenda topics of the meeting were:

  • Wolfram launch on 5/20 cancelled, postponed
  • Lynwood Unified Girl STEM conference, 6/1
  • Funding received for 60ft launch rail, prefabbed containers, solar panels
  • USC upgrade proposal for horizontal pad
  • 6/10 UCLA launch event
  • 7/21 Aerospace launch event
  • Larry CalFire recommendation letters
  • Discussion of 45kW power generator purchase
    • Our current generator is only 7kW
    • Society will likely need to replace the current generator
  • Liquids and Cryogenic Fluid Handling class
    • Cryogenic Training, Colorado School of Mines, 7/31-8/4

Past Events

There was a launch event scheduled for May 20th, held for society member Wolfram’s personal project. Unfortunately, he suffered from a pinched nerve on the day of the launch, and chose not to make the drive to the MTA while dealing with the pain. We’ll have future opportunities for Wolfram’s next test flight of his 2-stage Gas Guzzler rocket.

On June 1st, Society Secretary represented the Society at the Lynwood Girl’s STEM conference. The Society was last represented at this event a few years ago, so it is appreciated that Joel took the time out of his busy schedule to attend.

The Society is pleased to announce that we have received funding for a number of planned improvements to the MTA. Some of the money is set to pay for new solar panels, as well as to pay for the previously installed one. Two other items paid for here are a prefabbed containers, one a 20ft office space, and the other a 40ft crew cabin. Finally, and arguably the most important, is money for a proposed 60ft launch rail for liquid rockets. A final design for the same has not been chosen yet, but proposals are currently being sought out from various sources by the Executive Council.

Current Events

USC is currently proposing making improvements to the short launch tower at the MTA. Our contact who has proposed this project is currently set to graduate from the school this year, so time is likely of the essence. His proposal however, surely to everyone’s pleasure, is to set female anchors into the concrete pad.

There is a launch event set for June 10th. There are two groups who will be using the site on that day. One is a children’s group led by Frank and Larry. They will be launching B and C rockets, and Baby Berthas. The second group to use the site on that day will be UCLA, who will be launching F and G rockets. This is a senior capstone project for their students. At the same time, Dave and Joel will be traveling there to handle UCLA, and Dave will be bringing some more supplies for the restroom.

In regards to the restroom, Dave is pleased to announce that it has passed the initial tests, and is functional. However, the water heater for the shower and sink has not yet been installed. It’s first live demonstration will be at the 6/10 Launch Event tomorrow.

The society is pleased to announce that we had a new member attend our meeting this month. Adrew Fuller is an intern at Northrop Grumman, and was invited by his coworker and fellow member, Michael R. During the discussion with him, it was brought up that a Northrop Grumman internet launch event might be proposed.

Also, Bill Inmann mentioned towards the end of the meeting that he’s made some upgrades to his Solar Cat steam rocket. He has apparently made the controls of the rocket wholey wireless, which could improve safety immensley.

*Future Events

On July 21st, the Aerospace Corporation is set to have a launch event at the MTA. Aerospace has agreed to pay the full MTA price, for what will be an internet launch event. Aerospace employee Jerry Fuller is also set to do a hybrid launch.

Society Treasurer Larry has previously expressed a desire to discuss Calfire recommendation letters, however, as of the time of this meeting, he has requested that the discussion be tabled. It was mentioned by other members that Caleb Phillips is our contact at Calfire, and he has apparently made some comments in regards to the difficulties in acquiring the number of recommendations required for obtaining a license. One idea suggested is the minimum number being no more than some proportion of current license holders in total. It was also brought that, in regards to obtaining a class 3 license, CALFIRE truly only asks for a few recommendations from other Pyro-ops, and will accept some references from non-family me,bers which are only character references in nature.

Another future issue discussed was in regards to the purchase of a 45kw power generator. It needs to be determined what are the MTA’s power needs, and this will have to be done by measuring the appliances there. It should also be determined how many appliances should be in operation at once on the site. It was suggested that we should ask FAR what their average power usage is, to use as a baseline. The importance of this discussion will increase as time continues on, since the Society will need obtain a new generator in the next several years.

In regards to upgrades, the Society’s donors would like to receive an all-in figure the cost of upgrades we would like. President Dave has been working on producing a figure, and our donors haven’t yet agreed to it as a whole, but our best bet is to try and demonstrate our ability to carry out the upgrades in a timely fashion, and on budget, in order to make use of their generosity.

Regarding usage of the MTA, Vice-President Frank has scheduled another class. This one is for the Boyle Heights YMCA. He’s currently planning to host their launch on September 9th.

Keith Yoerg has again brought up that the society could surely use more launchers at the MTA. If they were portable then they would be better yet, since they could be repositioned as needed, to be best viewed from the blockhouse. He has again mentioned that he would like to see regularly scheduled events held at the MTA, to drum up interest in rocketry, and the Society. Keith and Michael Rouleau were going to investigate designs of a multi-rail launcher with six 1010 rails. The council approved funding for this important improvement to aid in future launch events.

Frank was also pleased to announce that Mary Star, the location for this year’s Symposium, has already scheduled us to host it there again next year, on April 13th. Having a set date and location will make planning much easier than it was this year, and we are pleased again with Frank’s hard work.

The next society meeting will be on July 14th, 2023, at the Compton/Woodley Airport location. Contact the secretary for details. We meet the 2nd Friday of each month at 7:30pm.


May 2023 Meeting

by Joel Cool-Panama, Secretary, RRS.ORG


The Reaction Research Society held its monthly meeting at the Compton/Woodley Airport location, 7:30 PM PST.

Agenda topics of the meeting were:

  • Symposium successes
  • Restroom operational
  • MTA improvements
  • Wolfram launch 5/20
  • UCLA launch 6/10

Past Events

It is with great pleasure that the Society declares the Symposium to have been a success. In all, there were 22 presenters present, and approximately 70 to 80 persons in attendance. Likewise, Mary Star High School has told us that they did well on their food service sales, and have already penciled us in to host the Symposium at their location again on April 8th, 2024.

However, there is much room for improvement. For example, we need to have better signage for the presentation room and food service at the next symposium. We could also take advantage of the large screens present in the gymnasium to keep attendees up to date on presentations. It was also noted that we should have a hard deadline for speakers to sign up, probably a few days in advance of the event, to prevent scheduling confusion. The older members of the Society are also in agreement that we should hire some of the students to help us setup and break down the Symposium. We could also Mary Star’s WiFi password, and maybe make it available upon request.

The Society was also pleased to receive a donation of eletrical match blanks from long-time RRS member, Steve Majdali. Our treasurer, Larry Hoffing, is to write a receipt for them.

Current Events

Prior to the meeting, Society President Dave Nordling had new keys made for the newly opened MTA restrooms. Six pairs of keys were made, the gold one being to open the restroom proper, and the silver to open the container door to the valves and switches.

In regards to the restroom, it was mentioned that the society should probably hire someone to clean the restroom. In the past, society members have graciously handled cleaning and supplies themselves with the porta-potties, but there is a desire to have the restrooms taken care of by someone else. The main problem seems to be the cost of doing so, and how we might extract compensatory fees from anyone who uses the MTA and doesn’t clean up after themselves. A deposit was suggested, but Frank noted that getting such from a school would likely be a hassle.

Thanks to the Society’s generous donors, we are pleased to announce that a 60-foot launch rail for launching liquid rockets, and prefabbed containers for the MTA, have been funded. Polaris has a design for such a launch rail, and the Society is considering hiring them to build it. Also, in light of the struggles around building numerous projects at the MTA, it is expected that the Society will pay contractors to make improvements to the site mifor the forseeable future.

It’s also been recommended that the Society should have portable launch rails at the MTA. Being portable means that they can be moved away when might be necessary, such as if a group’s view of another launch rail is obstructed. Wolfram in particular has requested 1515 launch rails, but others, such as members of ROC, might appreciate these as well, due to the difference between our height waivers.

Steve Majdali mentioned at the meeting that he has 1,000 ft of duplex wire, 18 gauge solid core, which he might donate to the Society for our use. He also apparently has multi-strand, fine gauge wire, and might even have some sulfur to dispose of as well.

In other news, Society Treasurer Larry has received 3 lbs of 400-mesh zinc powder from a supplier in India. The zinc isn’t of the fineness typically used for micrograin rockets, but Larry will test its use regardless. It should be noted that the zinc was bought at $4 per pound, which is a very good deal, and we might consider sourcing from this supplier in the future. US-based suppliers are not as common today as they have been in decades past.

Future Events

UCLA is currently scheduled to hold their Capstone project launch event at the MTA on June 10th. Likewise, Frank and Larry will simultaeneously be holding launch classes at the site. They will be having two launches, B and C motor model rockets, as well as Baby Bertha.

The Aerospace Corporation is also scheduled to use the MTA for their intern rocket launch event. As of now, there is no conflict on the MTA schedule with their event.

The Society is also receiving more requests for Vice-President Frank to teach more classes. Among past locations requesting his services is Nickerson Gardens.

Also, it has been noted that having underground cable runs between the launch rails and the Garboden Observation Bunker at the MTA would be very valuable. A pull string should be installed along with whatever conduit is put in place, and CAT9 wire should definitely be installed as a good starting point. This facility improvement needs further definition.

The next society meeting will be on June 9th, 2023, at the Compton/Woodley Airport location. Contact the secretary for details.


Launch Event, 2023-04-22

by Bill Claybaugh, RRS.ORG


Editor’s Note:

RRS member, Bill Claybaugh, built and launched his second 6-inch rocket from the RRS Mojave Test Area on Saturday, April 22, 2023. Target apogee was 69,000 feet. Winds were very low that day. Jim Gross was the pyrotechnic operator in charge for the launch event. Dimitri Timohovich and Rushd Julfiker assisted with the efforts. Bill launched from a 24-foot aluminum channel type launch rail using a pair of belly-bands that disconnected from the vehicle after clearing the end of the rail. The following is Bill’s update report on the flight as of July 1, 2023.


Flight 2 – Six Inch Rocket

Fight II Flight Report

Introduction

Something fairly violent happen to this vehicle at about 3.4 seconds into flight: onboard data and ground video indicate the rocket pitched at least 30 degrees while traveling at about Mach 2.2 at around 4100 feet above ground level (AGL).

Recovered hardware indicates the vehicle broke up under these conditions.  The parachute compartment, which was attached to the top of the motor by four ¼-20 fasteners, was torn away by fracture at all four fasteners (the fasteners remained attached to the motor). The payload, which was attached to the parachute compartment via four 0.250” diameter pneumatic separation system pins, remained attached—indeed, it was recovered with the separation system still functional and still latched to the top of the parachute compartment.

Bill Claybaugh with his second 6-inch rocket before launch.

Video shows a sudden pitch at about 3.4 seconds after first vehicle motion.  The onboard data (which records the initial part of the breakup because the computer was located in the payload section) shows that the gyro tilt went from about 5 degrees to 50 degrees over 0.08 seconds.  Measured longitudinal acceleration went from the previous around 26 g’s to 34 g’s in 0.05 seconds, and after returning to around 24 g’s for 0.15 seconds, to -12.7 g’s (the sensor floor) for 0.03 seconds, before recovering to -9 g’s for 0.01 seconds followed by loss of power. (See Chart 1.)

Chart 1: Acceleration and Tilt

Video shows the vehicle recovering from this pitch maneuver and continuing on a near vertical ascent though burnout at a video-based about nine seconds after first motion.

Flight

Following failure of the AlClO (Aluminum / Potassium Perchlorate) based head end initiator to successfully ignite the rocket (AlClO based initiators have had this issue previously, AlClO appears to be too energetic for this application, tending to blow the secondary ignition materials out the back of the rocket and on to the ground rather than igniting the grain) a jury-rigged rear end ignitor was substituted and the rocket successfully lifted off about 0.25 seconds after flames first appeared around the vehicle base.

Onboard data shows the vehicle ascending at about 88 degrees from horizontal to about 50 feet altitude when a lazy “S” turn (first to the northeast, then back to the southwest) is visible in the video and data. This turn starts about the time the belly-bands can be seen on video falling away from the vehicle.

Following this maneuver, the vehicle returns to near vertical flight to the Southwest, turning, with perturbations, from about 88 degrees tilt to an 86-degree gyro tilt over the next two-plus seconds.  Acceleration steadily builds from an initial 18.6 g’s to a maximum of 27.3 g’s at 2.53 seconds; this acceleration broadly follows the curve expected from the combination of the thrust curve, drag, and the lessening weight of the vehicle as propellant is consumed, however, the measured acceleration is much higher than expected based on static tests and flight simulations.

Telemetry reported Loss of Signal (LOS) at 2.7 seconds and at an (accelerometer-based) 2313 feet altitude and 2440 ft/sec velocity.

Measured onboard acceleration suddenly jumps from a base around 26.5 g’s at 3.18 seconds to 32.8 g’s at 3.21 seconds; measured onboard acceleration stays above 30g’g for the next 0.06 seconds, peaking at 34.7 g’s at 3.21 seconds and followed by a return to around 24 g’s for 0.15 seconds and a sudden drop to -12.7 g’s (the sensor floor) from 3.42 to 3.44 seconds and a final reading of -9.3 g’s followed by loss of power to the on-board computer.

Onboard data shows the gyro tilt angle moving from around 5 degrees at 3.37 seconds to 50.6 degrees at 3.45 seconds, followed by loss of power.

Video over this period show the vehicle suddenly turning through an apparent (visual) 30 degrees or so before pitching back to a near vertical ascent.

Analysis

A less energetic initiator is required for this vehicle; a development program will be initiated to achieve both a more reliable and a gentler ignition in future.

Figutr 1: Recovered Nozzle

Following flight, a single sliver of graphite was found on the ground about 150 feet from the launch tower.  This piece of graphite was exactly the correct shape to fit at the very rear of the graphite throat insert where that insert blends into the titanium nozzle extension. 

Recovered nozzle hardware showed that about 1-inch of the rear of the nozzle insert was missing (see Image 1); assuming the two pieces of the insert found inside the rocket were broken by impact forces, it follows that around one inch at the rear of the insert failed prior to impact. This failure would have induced a flow discontinuity in the rocket’s exhaust which thrust vector could account for the sudden pitch at 3.4 seconds into flight. The vehicle’s return to near vertical ascent appears to be due to aerodynamic assisted dampening of the perturbation, based on the tilt data from the earlier–possibly belly-band related–slow spiral of the vehicle.

Note that the recovered nozzle shows plating of Aluminum Oxide onto the ZrO coated Titanium nozzle extension above the end of the graphite nozzle extension but not in the area originally covered by the graphite insert.  This suggests the insert was present during startup (when Aluminum Oxide would be expected to condense on the nozzle extension surface) and the loss of the about 1-inch of the bottom of the graphite nozzle insert must have occurred later.

Analysis indicates that thermal stress cannot have been the cause of the loss of the back of the nozzle insert: maximum thermal stress occurs at the throat and reaches no more than 60% of the tensile strength of the graphite.  Careful measurement shows that the break occurred at the location of the joint between the titanium nozzle extension and the aluminum nozzle support structure, it thus appears that a (possibly heating related) stress concentration at that location was the probable cause of the graphite failure.

Loss of telemetry at 2.7 seconds appears to be a consequence of the GPS and transmitter antenna assembly failing mechanically; the flight computer was recovered with a clean break at the antenna PCB board.  This suggests the need for more robust support of these parts of the payload.

Breakup of the vehicle began about 3.41 seconds after launch.  The recovered pieces indicate separation of the parachute compartment from the motor was due to the upper part of the vehicle being pulled longitudinally forward, away from the (thrusting) rocket motor; further, the fracture pattern indicates an abrupt failure rather than a slightly slower swaging of the metal.  Based on the acceleration data indicating at least four hundredths of a second of significant negative g’s just before loss of power, coupled with gyro data showing the payload being thrown through an about 45 degree turn over the last 0.08 seconds of data, we can guess that the mechanical failure was a consequence of rather than the cause of the sudden turn of the vehicle.

Figure 2: Booster, post-impact

Actions

Development of a gentler and more consistent initiator is required; an effort focused on BKNO3/V (Potassium Nitrate with Boron held in a Viton matrix) has been started.

The vehicle nozzle has been redesigned to use a single piece titanium throat insert support structure and nozzle extension.  The angle of the joint between the graphite insert and the titanium shell has been increased to the conventional 5 degrees (the flight nozzle used a 3-degree angle that may have been too thin at the very end of the throat insert).

Heat paint testing of the Titanium nozzle extension on the flight nozzle indicated a maximum heat soak temperature of about 800° degrees Fahrenheit on the outside surface; this suggests a maximum outside wall temperature during operation of about one-half the paint-indicated heat-soaked temperature. Since these temperatures are well below the maximum working temperature of 6Al4V Titanium under these loads, the new nozzle is designed to allow for greater heating of the shell.

Analysis based on assuming a maximum Titanium temperature during operation of about 400° F indicates a maximum possible temperature of about 1140° degrees at the ZrO / Titanium interface and about 2800 °F at the inside surface of the Graphite insert, implying a maximum surface temperature at the nozzle throat of about 4350 °F.  A similar analysis indicates a maximum possible temperature at the inside surface of the nozzle exit of about 3300° F.

The high temperature RTV layer between the graphite insert and the ZrO layer was originally 0.005” in thickness in two sections separated by a 0.030” cork layer (a total of 0.010” of RTV); it thus should have had sufficient space, after pyrolysis of that layer, to accommodate the estimated 0.0024” thermal expansion of the Graphite Nozzle Insert.

The payload internal fiberglass support structure for the flight computer failed both at the base and at the antennae.  This structure will be redesigned in aluminum so as to provide still more robust support to the flight computer assembly.  Making this change will reduce the sensitivity of the GPS antenna and will absorb some of the transmitted energy from the telemetry antenna (the reason for going with fiberglass previously).  The effects of lower sensitivity will have to documented once that hardware is available and assembled.

The measured inflight acceleration is significantly higher than that expected from static testing and modeling of the flight trajectory; however, the burn time indicated from multiple videos is about that expected from motor modeling and the previous static test.

Analysis of the cause of the apparently higher than expected thrust has proven inconclusive.  A grain crack or void (possibly associated with the energetic AlClO initiator) would usually be expected to grow until the motor case failed.  The slightly higher than modeled initial grain area (see the report from the first flight of this vehicle for a discussion) is too small (at 0.86%) to account for the higher initial thrust (123% of the expected level). A static test motor is being prepared to try and resolve this question.

Strengthening the joint between the motor and the parachute compartment is relatively easy; additional fasteners and a thicker section to the joint should reduce the probability of a failure similar to that which occurred on this flight.  Alternatively, the motor tube could be extended by six inches to avoid having a separate parachute compartment altogether, albeit with some induced operational inconvenience when placing the initiator into the forward bulkhead.

Summary

Partial nozzle failure appears to be the main concern with this vehicle design; a secondary issue is strengthening internal components and some joints to better survive the extremely harsh conditions encountered on this flight. Finally, a cause for the apparently higher initial thrust will be sought via static testing of a new motor, which will also confirm the new nozzle design.